viewlab F1 update to c200

Обсуждение ViewLab F1 / Iconbit HD600Core (SMP8642)

Moderator: Модераторы

viewlab F1 update to c200

Postby kkaqier on Fri Dec 13, 2013 21:35

how to flash viewlab F1 to C200
kkaqier
 

Re: viewlab F1 update to c200

Postby None on Sat Dec 14, 2013 20:28

kkaqier wrote:how to flash viewlab F1 to C200

It's possible. The process is similar firmware reflash HDX-BD1 in C200.
BUT, it should be understood that by the LCD display and front panel buttons will not work. Probably will not work Wi-Fi.
And yet - reflash only possible to old version firmware C200 and is no possibility of update to new version.
Firmware BD-1_to_C200 is here:
http://www.mpcclub.com/forum/showthread.php?t=30530
Instruction there:
http://www.mpcclub.com/forum/showthread.php?t=27385
Warning!!!
Before you do this, you should stock up on the console adapter to save installed on player firmware. Xenv block of firmware is unique for each player, it is required to keep. Otherwise you will lose the opportunity to return to the original firmware.
Тренируйте лоб, ещё очень много не пробитых стен!
User avatar
None
Administrator
 
Posts: 1162
Joined: Tue Nov 02, 2004 10:19
Location: Москва

Re: viewlab F1 update to c200

Postby kkaqier on Sun Dec 15, 2013 14:46

Return to the original firmware is easy. I update to c200 ,but stop "LOGO loading" picture
kkaqier
 

Re: viewlab F1 update to c200

Postby None on Mon Dec 16, 2013 15:21

kkaqier wrote:Return to the original firmware is easy. I update to c200 ,but stop "LOGO loading" picture

Something specific in this situation, you can say if you show boot log, obtained from the console.
Тренируйте лоб, ещё очень много не пробитых стен!
User avatar
None
Administrator
 
Posts: 1162
Joined: Tue Nov 02, 2004 10:19
Location: Москва

Re: viewlab F1 update to c200

Postby kkaqier on Sun Dec 22, 2013 18:08

None wrote:
kkaqier wrote:Return to the original firmware is easy. I update to c200 ,but stop "LOGO loading" picture

Something specific in this situation, you can say if you show boot log, obtained from the console.

the TTL message has not save.I use hard disk flash 4ths FW ,(same to dune FW),but fail
Code: Select all
39idxfs696b15f57c540829defeeee9f4a092007337a124S

#xos2P52-100 (sfla 128kbytes. subid 0x00/9b) [serial#7f772c9df39be6e703a7005af3fc3ce5]
xmb 0xb5
No valid zxenv found in device group 0 CS#0
No valid zxenv found in device group 0 CS#1
No valid zxenv found in device group 1 CS#0
No valid zxenv found in device group 1 CS#1
SATA drive spin-up in progress, please standby...
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#28#2a#28#28# (20)
#DRAM1 Window  :    0x#28#28#28#28# (20)
#DRAM0 Settings: WD=0x0b0b0c0b RG=0x090a0909 RR=0x090a0909 RF=0x0a0b0b0b
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x09090909 RR=0x09090909 RF=0x0a0a0a0a
#poisoned 131072 pages with 0x666d5f2f
#st*** zxenv has been customized compared to build ***
--- review xmasboot/configs/922-A3a.config for details [xmbad-ezboot82-nand_st2] ---
xloadsize=46260
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot82 @0xd0105d70 (nand_st2) (actual cpu=@499MHz/dsp=333MHz/sys=333MHz)
on 8642 rev ES3 (subid 0x00) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x80042233,0x8f634000[ (~257891789 bytes)
ruamm1 [0xc88b17d5,0xcfd60000[ (~122349611 bytes)
[0xcfd20000,xos_public_ga=0xcfd20000[ and [0xcfd40000,0xcfd5ffff[ are lost for alignment)
x_ga=0xcfd1fcd4
[0x8e634000,ios_ga=0x8e800000[ and [0x8eeacfc1,0x8f633fff[ are lost for alignment)
GW32 0x0006f008 0xc0000000 [va=0x84000000]
GW32 0x0006f00c 0xc4000000 [va=0x88000000]
GW32 0x0006f010 0xc8000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = 696b15f57c540829defeeee9f4a092007337a124 (version 0x52)
xos2 serial = 7f772c9df39be6e703a7005af3fc3ce5
Using zbootxenv ga=0xcfd0bcbc (va=0xbbd0bcbc)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Started at 0xd010edd0.
* Configurations (chip revision: 1):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x3514001a/0x4565132b).
Using UART port 0 as console.
Board ID.: 922-A3a
Setting up H/W from XENV block at 0xbbd0bcbc.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000130.
  Setting <IRQ rise edge trigger lo> to 0xff28ca00.
  Setting <IRQ fall edge trigger lo> to 0x0000c000.
  Setting <IRQ rise edge trigger hi> to 0x0c10009f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0800.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001b3efc
    PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
  PCI IRQ routing:
    IDSEL 1: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 3: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
    IDSEL 4: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
  Smartcard pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
  Smartcard1 pin assignments:
    OFF pin = 2
    5V pin = 0
    CMD pin = 1
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 want 33333333Hz: setting of 0x0000000061333343-2^28
cd#4 measured to 33328kHz
cd#5 disabled
cd#6 disabled
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00000880/0x00000880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x00/0x00/0x00
  Generate pulse(s) with GPIO7 .. 1,0(10000us),1
  MAC0: 00:16:e8:77:2c:9d
  MAC1: 00:16:e8:a7:00:5a
XENV block processing completed.
Default boot index: 0
xmboot booted from devtype: 4, chipsel: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
  0x01 : devtype=0, CS=1
  0x20 : devtype=2, CS=0
  0x21 : devtype=2, CS=1
xmat romfs goes to 0xcfb0bca0 (ga)
xmat romfs goes to 0xb3b0bca0 (va)
Trying devtype=0 chipsel=0
gbus_read_unit32 0x0xd0103448 0x0xd0103448
nand_handle 0xd011ec40 st_partition 0
nand_handle.p_partition 0xd011e59c.......
nand_probe 0x0xd0115a14
nand_Mg_open 0
Reading NAND CS0, addr 0x01800000, maxsize 0x00200000 to 0xb3b0bca0
Did not find a valid xmat romfs in devtype0 CS#0
Trying devtype=0 chipsel=1
gbus_read_unit32 0x0xd0103448 0x0xd0103448
nand_handle 0xd011eecc st_partition 1
nand_handle.p_partition 0xd011e59c.......
nand_probe 0x0xd0115a14
Failed to init!
Trying devtype=2 chipsel=0
Did not find a valid xmat romfs in devtype2 CS#0
Trying devtype=2 chipsel=1
SATA drive spin-up in progress, please standby...
Failed to init!
Failed to find valid xmat romfs in any device / chip select!
freeing xmat romfs buffer at 0xcfb0bca0
xmat romfs process failed.
found imat romfs @ 0x00800000
imap romfs goes to 0xcf40bca0 (ga)
imap romfs goes to 0xb340bca0 (va)
Trying devtype=0 chipsel=0
Reading NAND CS0, addr 0x00800000, maxsize 0x00900000 to 0xb340bca0
Did not find a valid imat romfs in devtype0 CS#0
Trying devtype=0 chipsel=1
gbus_read_unit32 0x0xd0103448 0x0xd0103448
nand_handle 0xd011eecc st_partition 1
nand_handle.p_partition 0xd011e59c.......
nand_probe 0x0xd0115a14
Failed to init!
Trying devtype=2 chipsel=0
Did not find a valid imat romfs in devtype2 CS#0
Trying devtype=2 chipsel=1
SATA drive spin-up in progress, please standby...
Failed to init!
Failed to find valid imat romfs in any device / chip select!
freeing imat romfs buffer at 0xcf40bca0
imat romfs process failed.
Trying devtype=0 chipsel=0
reading z.boot0 (vzx=0xbbd0bcbc) is 0x00080000
Reading NAND CS0, addr 0x00080000, maxsize 0x01000000 to 0x88100000
Reading NAND CS0, addr 0x00080000, size 0x0002f800 to 0x88100000
Found.
ROMFS found at 0x0x88100000, Volume name = YAMON_XLOAD
Found 1 file(s) to be processed in ROMFS.
Processing yamon-xload.zbf (start: 0x88100080, size: 0x0002f5e4)
  Checking zboot file signature .. OK.
  Warning: header version mismatched.
   *** Fully Encrypted.
src addr = 0xb1800000, dest addr = 0x13000000, is_dest_gaddr = 0x00000010
XLOADING src=0x81800000, dest=0x13000000, size=0x0002f5c4
xload.c:63: Waiting for XLOAD completion.
xload.c:73: XLOAD done, status = 0x6.
  Decompressing to 0x85200000 .. OK (357824/0x575c0).
  Load time total 0/0 msec.
Execute final at 0x85200000 ..

CS 0 vendor id 0xec.......
CS 0 device id 0xda.......
................................................................................................................................................................................................................................................................doing Super block Sanity checks... location 4
doing Managment block Sanity checks ...

CS 1 vendor id 0x00.......
CS 1 device id 0x00.......



**********************************
* YAMON ROM Monitor
* Revision 02.13-SIGMADESIGNS-24-R2.13-24
**********************************
Memory:  code: 0x86000000-0x86060000, 0x85200000-0x85204000
reserved data: 0x86200000-0x86300000, 0x86700000-0x87000000
PCI memory: 0x86300000-0x86700000



NAND FLASH Driver Version [ S I G M  1.0.6 ] on CS 0

!! No NAND hardware found on CS 1 !!


Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

to 0x00100000
doing Super block Sanity checks... location 4
doing Managment block Sanity checks ...

NAND has already been formated and data will be lost in this process !!!
Eraseing data block ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................old format found, NAND lib is conerting the old to new format....
.................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
Erasing dirty blocks.. !!!
.Dirty block found 4
.Dirty block found 5
............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Dirty block found 1025
.Dirty block found 1026
.............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
ret 0 Eraseing management block ....791.792.793.794.795.796.797.798.799.800.801.802.803.804.805.806.807.808.809.810.811.812.813.814.815.816.817.818.819.820.821.822.823.824.825.826.827.828.829.830.831.832.833.834.835.836.837.838.839.840.841.842.843.844.845.846.847.848.849.850.851.852.853.854.855.856.857.858.859.860.861.862.863.864.865.866.867.868.869.870.871.872.873.874.875.876.877.878.879.880.881.882.883.884.885.886.887.888.889.890.891.892.893.894.895.896.897.898.899.900.901.902.903.904.905.906.907.908.909.910.911.912.913.914.915.916.917.918.919.920.921.922.923.924.925.926.927.928.929.930.931.932.933.934.935.936.937.938.939.940.941.942.943.944.945.946.947.948.949.950.951.952.953.954.955.956.957.958.959.960.961.962.963.964.965.966.967.968.969.970.971.972.973.974.975.976.977.978.979.980.981.982.983.984.985.986.987.988.989.990.991.992.993.994.995.996.997.998.999.1000.1001.1002.1003.1004.1005.1006.1007.1008.1009.1010.1011.1012.1013.1014.1015.1016.1017.1018.1019.1020.1021.1022.1023.1024.1025.1026.1027.1028.1029.1030.1031.1032.1033.1034.1035.1036.1037.1038.1039.1040.1041.1042.1043.1044.1045.1046
ret 0 Eraseing super block ....4.5
ret 0 creating super block and management block.....273: is bad
1786: is bad
1975: is bad
1984: is bad
old format found, NAND lib is conerting the old to new format....


format process is completed.....

---------------- NAND Info ----------------------------

Size of NAND flash memory: 267911168 bytes
The size of block: 131072 bytes
The total Number of physical blocks: 2048
The total number of logical blocks: 1719
The number of used logical blocks: 0
The number of available logical blocks: 1719 (225312768 bytes)
CMD0
Reset timed out on port 1.
Reset timed out on port 1.
CMD1
Reset timed out on port 1.
Reset timed out on port 1.
Reset timed out on port 1.
Reset timed out on port 1.
kkaqier
 

Re: viewlab F1 update to c200

Postby None on Mon Dec 23, 2013 08:37

kkaqier wrote:
None wrote:
kkaqier wrote:Return to the original firmware is easy. I update to c200 ,but stop "LOGO loading" picture

Something specific in this situation, you can say if you show boot log, obtained from the console.

the TTL message has not save.I use hard disk flash 4ths FW ,(same to dune FW),but fail
So what? You asked about the C200, and here 4ths firmware is? :donno:
Тренируйте лоб, ещё очень много не пробитых стен!
User avatar
None
Administrator
 
Posts: 1162
Joined: Tue Nov 02, 2004 10:19
Location: Москва

Re: viewlab F1 update to c200

Postby kkaqier on Mon Dec 23, 2013 23:12

yes ,this TTL log is update to 4ths firmware.I try to update to 4ths firmware,after update to c200.
kkaqier
 

Re: viewlab F1 update to c200

Postby None on Tue Dec 24, 2013 10:41

kkaqier wrote:yes ,this TTL log is update to 4ths firmware.I try to update to 4ths firmware,after update to c200.

Our team did not do research 4th firmware. Not possible to give you advice, sorry.
Тренируйте лоб, ещё очень много не пробитых стен!
User avatar
None
Administrator
 
Posts: 1162
Joined: Tue Nov 02, 2004 10:19
Location: Москва

Re: viewlab F1 update to c200

Postby kkaqier on Wed Dec 25, 2013 20:39

None wrote:
kkaqier wrote:yes ,this TTL log is update to 4ths firmware.I try to update to 4ths firmware,after update to c200.

Our team did not do research 4th firmware. Not possible to give you advice, sorry.

I flash to C200 again,and TTL LOG here
Code: Select all
format process is completed.....

---------------- NAND Info ----------------------------

Size of NAND flash memory: 267911168 bytes
The size of block: 131072 bytes
The total Number of physical blocks: 2048
The total number of logical blocks: 1719
The number of used logical blocks: 0
The number of available logical blocks: 1719 (225312768 bytes)
YAMON> setenv bootserver 192.168.1.105
Please flush(using nflash/pflash write command) the updated transient XENV block
(memory location: 0xbb79bcb0, maximum size: 0x00004000) to the location desired
for permanent storage.
YAMON> net init
net have been initialized
ipaddr:     192.168.1.101
subnetmask: 255.255.255.0
gateway:    192.168.1.1
bootserver: 192.168.1.105
YAMON> load -b tftp:/tftp-recovery-01 0xa7000000;copy 0xa7000000 $xenv_addr 0x4000
About to load tftp://192.168.1.105/tftp-recovery-01
Press Ctrl-C to break
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................


Start = 0xa7000000, range = (0xa7000000,0xa8dfffff), format = BINARY
Length = 0x1e00000 (31457280)
Checksum = 0x0c49300d (10'206123021)

Copying...Done
YAMON> $r01
*** smp86xx_recover V1.0.4. Starting (23:22:25-20.04.2011)...
- Recovering section 14.1
- Recovering section 13.1
- Reading data #2:
About to load tftp://192.168.1.105/./tftp-recovery-02
Press Ctrl-C to break
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................


Start = 0xa7000000, range = (0xa7000000,0xa8dfffff), format = BINARY
Length = 0x1e00000 (31457280)
Checksum = 0x0dea9347 (10'233476935)

- Recovering section 13.2
- Recovering section 12.1
- Recovering section 10.1
- Recovering section 9.1
Part r01 Done! Please Run Part $r02:
YAMON> $r02
Starting Part r02...
- Reading data #3:
About to load tftp://192.168.1.105/./tftp-recovery-03
Press Ctrl-C to break
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................


Start = 0xa7000000, range = (0xa7000000,0xa8dfffff), format = BINARY
Length = 0x1e00000 (31457280)
Checksum = 0xdf2c6590 (10'3744228752)

- Recovering section 9.2
- Recovering section 8.1
- Recovering section 7.1
- Recovering section 6.1
- Recovering section 5.1
- Recovering section 4.1
- Reading data #4:
About to load tftp://192.168.1.105/./tftp-recovery-04
Press Ctrl-C to break
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................
................................................................


Start = 0xa7000000, range = (0xa7000000,0xa8dfffff), format = BINARY
Length = 0x1e00000 (31457280)
Checksum = 0xc29ff344 (10'3265262404)

- Recovering section 4.2
Part r02 Done! Please Run Part $r03:
YAMON> $r03
Starting Part r03...
- Recovering section 3.1
- Reading data #5:
About to load tftp://192.168.1.105/./tftp-recovery-05
Press Ctrl-C to break
................................

Start = 0xa7000000, range = (0xa7000000,0xa70fffff), format = BINARY
Length = 0x100000 (1048576)
Checksum = 0x7b9c9308 (10'2073858824)

- Recovering section 3.2
- Recovering section 2.1
- Recovering section 1.1
All Parts Done!!! Rebooting in 20 seconds...
Reboot immediately .
39idxfs696b15f57c540829defeeee9f4a092007337a124S

#xos2P52-100 (sfla 128kbytes. subid 0x00/9b) [serial#7f772c9df39be6e703a7005af3fc3ce5]
xmb 0xb5
#chpll 0x01000024/0x00000201 -> 0x01000030/0x00000101... actual sys=330MHz
#DRAM setup (method=0x10015858) ...
#DRAM0 Window  :    0x#26#28#26#28# (19)
#DRAM1 Window  :    0x#26#26#26#26# (19)
#DRAM0 Settings: WD=0x0b0b0b0b RG=0x09090909 RR=0x09090909 RF=0x0a0b0b0b
#DRAM1 Settings: WD=0x0b0b0b0b RG=0x09090909 RR=0x09090909 RF=0x0a0b0a0b
#poisoned 131072 pages with 0x6a9da3e2
#s*** zxenv has been customized compared to build ***
--- review xmasboot/configs/947-E2.config for details [xmbb7-ezboot98-nand_st2] ---
xloadsize=59476
xload rc=6
subrom SHA-256: 43b5383fcd2ecd1f5366bea4eafc03bd740dc0a113af58d02846c117fb581b5b
ezboot98 @0xd00e5a94 (nand_st2) (actual cpu=@661MHz/dsp=330MHz/sys=330MHz)
on 8642 rev ES3 (subid 0x00) a2=0x00000002 a3=0x00000003
step12
#step22
ruamm0 [0x8c000000,0x8f2f8000[ (~53444608 bytes)
ruamm1 [0xc0004000,0xcfff0000[ (~268353536 bytes)
[0xcffb0000,xos_public_ga=0xcffc0000[ and [0xcffe0000,0xcffeffff[ are lost for alignment)
x_ga=0xcffafcd4
[0xcf79fcbc,ios_ga=0xcf800000[ and [0xcfc00000,0xcff9fcbb[ are lost for alignment)
GW32 0x0006f008 0x80000000 [va=0x84000000]
GW32 0x0006f00c 0x84000000 [va=0x88000000]
GW32 0x0006f010 0x88000000 [va=0x8c000000]
step33
xos2k client version=19, server version=19
xos2 SHA-1 = 696b15f57c540829defeeee9f4a092007337a124 (version 0x52)
xos2 serial = 7f772c9df39be6e703a7005af3fc3ce5
Using zbootxenv ga=0xcf79bcb0 (va=0xbb79bcb0)

**************************************
* SMP86xx zboot start ...
* Version: 3.1.0
* Built on: May 25 2010 19:40:02
* Started at 0xd00edce4.
* Configurations (chip revision: 3):
*    Enabled checkpoints.
**************************************
DRAM0 dunit_cfg/delay0_ctrl (0x35140017/0x4565132b).
DRAM1 dunit_cfg/delay0_ctrl (0x35140017/0x4565132b).
Using UART port 0 as console.
Board ID.: 947-E2
Setting up H/W from XENV block at 0xbb79bcb0.
  Setting <SYSCLK avclk_mux> to 0x17400000.
  Setting <SYSCLK hostclk_mux> to 0x00000131.
  Setting <IRQ rise edge trigger lo> to 0xff288a06.
  Setting <IRQ fall edge trigger lo> to 0x00008000.
  Setting <IRQ rise edge trigger hi> to 0x0c10001f.
  Setting <IRQ fall edge trigger hi> to 0x00000000.
  Setting <IRQ GPIO map> to 0x000a0000.
  Setting <PB default timing> to 0x03080202.
  Keeping <PB timing0> to 0x03080202.
  Keeping <PB Use timing0> to 0x000003f3.
  Keeping <PB CS Config> to 0x00330003.
  Enabled Devices: 0x001103f8
    Ethernet Ethernet1 IR FIP I2CM I2CS SDIO USB SATA
cd#0 disabled
cd#1 disabled
cd#2 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#2 cannot measure
cd#3 disabled
cd#4 measured to 129600kHz
cd#5 disabled
cd#6 want 96000000Hz: setting of 0x0000000021c00000-2^28
cd#6 measured to 0kHz
cd#7 disabled
cd#8 disabled
cd#9 disabled
cd#10 disabled
cd#11 disabled
  GPIO dir/data = 0x00004880/0x00004880
  UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
  UART1 GPIO mode/dir/data = 0x00/0x00/0x00
  UART2 GPIO mode/dir/data = 0x00/0x00/0x00
  MAC0: 00:16:e8:77:2c:9d
  MAC1: 00:16:e8:27:00:5a
XENV block processing completed.
Default boot index: 0
xmboot booted from devtype: 0, chipsel: 0, phyblocknum: 0
Explicit boot order specified:
  0x00 : devtype=0, CS=0
ezboot buffers, setup in DRAM bank#0:
  Alloting 2097152 bytes for heap.
  Alloting 16777216 bytes for reading.
  Alloting 16777216 bytes for decryption.
xmat romfs goes to 0xcf59bca0 (ga)
xmat romfs goes to 0xb359bca0 (va)
Trying devtype=0 chipsel=0
nand_probe 0x0xd00f76a0
nand_Mg_open 0
Reading NAND CS0, addr 0x058c0000, size 0x00000800 to 0xb359bca0
Reading NAND CS0, addr 0x058c0800, size 0x0015fc00 to 0xb359c4a0
File xtask_loader.xload found
found imat romfs @ 0x04fc0000
imap romfs goes to 0xcec9bc80 (ga)
imap romfs goes to 0xb2c9bc80 (va)
Trying devtype=0 chipsel=0
Reading NAND CS0, addr 0x04fc0000, size 0x00000800 to 0xb2c9bc80
Reading NAND CS0, addr 0x04fc0800, size 0x003aa800 to 0xb2c9c480
File itask_loader.iload found
Trying devtype=0 chipsel=0
reading z.boot0 (vzx=0xbb79bcb0) is 0x00080000
Reading NAND CS0, addr 0x00080000, size 0x00000800 to 0x04240000
Reading NAND CS0, addr 0x00080800, size 0x0002f000 to 0x04240800
Found.
ROMFS found at 0x0x04240000, Volume name = YAMON_XLOAD
Found 1 file(s) to be processed in ROMFS.
Processing yamon-xload.zbf (start: 0x04240080, size: 0x0002f394)
  Checking zboot file signature .. OK.
  Warning: header version mismatched.
   *** Fully Encrypted.
src_addr = 0x042400a0, dest addr = 0x05240000
XLOADING src=0x842400a0, dest=0x85240000, size=0x0002f374
xload.c:77: Waiting for XLOAD completion.
xload.c:87: XLOAD done, status = 0x6.
  Decompressing to 0x85200000 .. OK (356320/0x56fe0).
  Load time total 0/0 msec.
Execute at 0x85200000 ..

CS 0 vendor id 0xec.......
CS 0 device id 0xda.......
................................................................................................................................................................................................................................................................doing Super block Sanity checks... location 4
doing Managment block Sanity checks ...

CS 1 vendor id 0x00.......
CS 1 device id 0x00.......



**********************************
* YAMON ROM Monitor
* Revision 02.13-SIGMADESIGNS-24-R2.13-24
**********************************
Memory:  code: 0x86000000-0x86060000, 0x85200000-0x85204000
reserved data: 0x86200000-0x86300000, 0x86700000-0x87000000
PCI memory: 0x86300000-0x86700000



NAND FLASH Driver Version [ S I G M  1.0.6 ] on CS 0

!! No NAND hardware found on CS 1 !!


Environment variable 'start' exists. After 2 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

  Checking zboot signature..  it's a zboot file, signature OK.
ZBOOT_ATTR_PHY_LOAD OFF
g_load_addr=0x80000000,g_base_addr=0x830000b0,count=0x0070ba74
Waiting for XLOAD completion.
XLOAD done. status = 0x6 .. OK.
ZBOOT_ATTR_GZIP ON
  Decompressing to 0x84000000 ..
Output length: 0x0097d755(9951061)
Decompressing decrypted data from 0xa70004c4 to 0x84000000 OK
Linux version 2.6.22.19-27-4 (release@earth) (gcc version 4.3.2 (Sourcery G++ Lite 4.3-51) ) #73 PREEMPT Mon Mar 7 14:50:40 MYT 2011
Mixed DRAM usage enabled.
Configured for SMP864x, detected SMP8642 (revision ES3).
Detected CPU/System/DSP Frequencies: 661.50/330.75/330.75MHz
SMP86xx Enabled Devices under Linux/XENV 0xcf79bcb0 = 0x001103f8
Ethernet Ethernet1 IR FIP I2CM I2CS SDIO USB SATA
Desired kernel memory size: 0x05000000
Max. DRAM0/1 size allowed: 0x0c000000/0x00004000
Mapped 0x80000000(size 0x04000000) via remap2
Mapped 0x84000000(size 0x01000000) via remap3
Final kernel memory size: 0x05000000
CPU revision is: 00019749
FPU revision is: 01739300
Determined physical RAM map:
memory: 05000000 @ 04000000 (usable)
Desired kernel memory size: 0x0c800000
Max. DRAM0/1 size allowed: 0x0c000000/0x00004000
Mapped 0x80000000(size 0x04000000) via remap2
Mapped 0x84000000(size 0x04000000) via remap3
Mapped 0x88000000(size 0x04000000) via remap4
Mapped 0xc0000000(size 0x00004000) via remap5
Final kernel memory size: 0x0c004000
User-defined physical RAM map:
memory: 0c004000 @ 04000000 (usable)
Wasting 131072 bytes for tracking 4096 unused pages
Initrd not found or empty - disabling initrd
On node 0 totalpages: 16385
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 16353 pages, LIFO batch:3
  Normal zone: 0 pages used for memmap
Built 1 zonelists.  Total pages: 16353
Kernel command line: console=ttyS0 mem=200M
Primary instruction cache 32kB, 4-way, physically tagged, linesize 32 bytes.
Primary data cache 32kB, 4-way, virtually tagged, no aliases, linesize 32 bytes
Synthesized TLB refill handler (19 instructions).
Synthesized TLB load handler fastpath (31 instructions).
Synthesized TLB store handler fastpath (31 instructions).
Synthesized TLB modify handler fastpath (30 instructions).
PID hash table entries: 1024 (order: 10, 4096 bytes)
Using 330.750 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 3, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 2, 65536 bytes)
Memory: 185488k/196624k available (3443k kernel code, 10880k reserved, 748k data, 5520k init, 0k highmem)
Calibrating delay loop... 330.13 BogoMIPS (lpj=1650688)
Mount-cache hash table entries: 2048
NET: Registered protocol family 16
PCI: pci host support disabled
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: TANGOX clocksource has been installed.
IP route cache hash table entries: 4096 (order: 0, 16384 bytes)
TCP established hash table entries: 8192 (order: 2, 65536 bytes)
TCP bind hash table entries: 8192 (order: 1, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
squashfs: version 3.4 (2008/08/26) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered
io scheduler anticipatory registered (default)
SMP86xx ir (254:0): driver loaded (wait_period = 100ms, buffer_size = 6)
fip: using hwi2c
SMP86xx fip (253:0): driver loaded (buffer_size = 2)
tango3dog: Hardware Watchdog Timer for SMP864x/SMP865x 0.1 (def. timeout: 30 sec)
Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
loop: module loaded
tangox_enet0: detected phy  at address 0x03
tangox_enet0: Ethernet driver for SMP864x/SMP865x internal MAC core 0: 100Mbps Base at 0x26000
tangox_enet0: mac address 00:16:e8:77:2c:9d
tangox_enet1: Ralink MII card not detected
k_name=Tangox SATA 0 driver=Tangox SATA 0
SATA version 0x3139302a ID 0x0 is detected
scsi0 : Tangox SATA 0
ata1: SATA max UDMA/133 cmd 0xa0023000 ctl 0xa0023020 bmdma 0xcdcdcdcd irq 49
ata1: SATA link down (SStatus 0 SControl 310)
k_name=Tangox SATA 1 driver=Tangox SATA 1
SATA version 0x3139302a ID 0x0 is detected
scsi1 : Tangox SATA 0
ata2: SATA max UDMA/133 cmd 0xa0023800 ctl 0xa0023820 bmdma 0xcdcdcdcd irq 62
ata2: port is slow to respond, please be patient (Status 0x80)
ata2: device not ready (errno=-16), forcing hardreset
ata2: port is slow to respond, please be patient (Status 0x80)
ata2: COMRESET failed (errno=-16)
ata2: port is slow to respond, please be patient (Status 0x80)
ata2: COMRESET failed (errno=-16)
ata2: port is slow to respond, please be patient (Status 0x80)
ata2: COMRESET failed (errno=-16)
ata2: COMRESET failed (errno=-16)
ata2: reset failed, giving up
CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 00000000, ra == 8403196c
Oops[#1]:
Cpu 0
$ 0   : 00000000 00000000 00000000 00000001
$ 4   : 00000000 0000003e 00000000 00000000
$ 8   : 11001c00 1000001f 00000000 8e11c000
$12   : 00000025 8436f4ec 00000000 84ac58c4
$16   : 00000000 00000000 849c0000 849c0000
$20   : 84361244 843a2cb0 8439fe50 a006e300
$24   : 00000000 84274a50                 
$28   : 84aa0000 84aa3ce0 84980000 8403196c
Hi    : 00000040
Lo    : 00000038
epc   : 00000000 _stext+0x7bffc000/0x160     Not tainted
ra    : 8403196c tasklet_action+0x94/0x11c
Status: 11001c03    KERNEL EXL IE
Cause : 40808008
BadVA : 00000000
PrId  : 00019749
Modules linked in:
Process swapper (pid: 1, threadinfo=84aa0000, task=84ac2d08)
Stack : 00001134 00001134 00001134 8402abdc 849ba244 00000000 0000000a 849c0000
        00000001 849bbcfc 849ba21c 84031edc a006e318 a006e300 84980000 840584e0
        00000000 00000000 8440ef80 843f7150 00000017 00000003 a006e318 84031fe4
        84980000 840586a8 c0fb8b80 0098963a 00400000 84032174 00400000 00000000
        8440ef80 843f7150 00000017 840058c0 8e140000 84aa3da0 8e67cc90 8e67cc90
        ...
Call Trace:
[<8402abdc>] release_console_sem+0x154/0x3f8
[<84031edc>] __do_softirq+0x84/0x120
[<840584e0>] handle_IRQ_event+0x64/0xbc
[<84031fe4>] do_softirq+0x6c/0x74
[<840586a8>] __do_IRQ+0x170/0x1b8
[<84032174>] irq_exit+0x5c/0x74
[<840058c0>] plat_irq_dispatch+0x358/0x508
[<84440000>] netdev_boot_setup+0xb4/0x144
[<840092a0>] ret_from_irq+0x0/0x4
[<84275c2c>] hsata_link_check+0x0/0x60
[<84440000>] netdev_boot_setup+0xb4/0x144
[<84274a50>] hsata_scr_read+0x0/0x30
[<842759c8>] hsata_probe+0x204/0x458
[<842759c0>] hsata_probe+0x1fc/0x458
[<8423d330>] driver_sysfs_add+0x6c/0xa0
[<8423d4e0>] driver_probe_device+0xf8/0x2a4
[<841f3728>] kobject_uevent_env+0x2f8/0x540
[<8423d8ec>] __driver_attach+0x260/0x268
[<8423d68c>] __driver_attach+0x0/0x268
[<8423c85c>] bus_for_each_dev+0x60/0xc8
[<84440000>] netdev_boot_setup+0xb4/0x144
[<8423bcdc>] bus_add_driver+0xb0/0x218
[<8443e4fc>] init_sg+0x19c/0x1e8
[<8423d8f4>] __device_attach+0x0/0x8
[<8443e64c>] tangox_hsata_module_init+0x5c/0xd8
[<84440000>] netdev_boot_setup+0xb4/0x144
[<8441c37c>] kernel_init+0xd4/0x33c
[<8441c2a8>] kernel_init+0x0/0x33c
[<8400b5c0>] kernel_thread_helper+0x10/0x18


Code: (Bad address in epc)

Kernel panic - not syncing: Fatal exception in interrupt
kkaqier
 

Re: viewlab F1 update to c200

Postby None on Thu Dec 26, 2013 10:01

kkaqier wrote:
None wrote:
kkaqier wrote:yes ,this TTL log is update to 4ths firmware.I try to update to 4ths firmware,after update to c200.

Our team did not do research 4th firmware. Not possible to give you advice, sorry.

I flash to C200 again,and TTL LOG here

Strange log. What image of HDD did you use? I recommend to use the method described recommend here:
http://www.sigmaplayer.com/viewtopic.php?t=2465&f=1
If the automatic mode does not work, then do the hands and step by step, following the reaction of the player, this method provides a more adequate result.
Тренируйте лоб, ещё очень много не пробитых стен!
User avatar
None
Administrator
 
Posts: 1162
Joined: Tue Nov 02, 2004 10:19
Location: Москва

Next

Return to ViewLab F1 / Iconbit HD600Core

Who is online

Users browsing this forum: Web crawler and 0 guests